Sublimation Blanks


	Blanks

		ALUMINUM: Now the reliability and quality of Unisub aluminum is available in an assortment of stamped blanks. Choose from a variety of sizes in a thickness of 0.030”

Part #	Description	Size	Case Qty	Each	Case	4+ Cases
UNI5730	Aluminum rectangle – square corners	1”x 3”	100	0.32	0.31	0.30
UNI5731	Aluminum rectangle – square corners	2.5” x 3.5”	50	0.60	0.57	0.56
UNI5749	Aluminum rectangle – round corners	3.375” x2.125”	50	0.90	0.86	0.84
UNI5732	Aluminum rectangle – round corners	5” x 7”	25	2.05	1.96	1.92


	FR Plastic Name Plate - These FRP blanks will fit the 1/8” name plate holders.

Part #	Description	Size	Case Qty	Each	Case	4+ Cases
UNI5579	Name Plates, 2/S, Gloss	2"x8"	25	3.01	2.87	2.82
UNI5580	Name Plates, 2/S, Gloss	2"x10"	25	3.01	2.87	2.82


	Car Dash Plates

		Automobile shows and clubs across the country give away dash plates to commemorate events. Now you can take advantage of this market opportunity. Made from 0.030” Unisub aluminum for durability and vibrant color.

Part #	Description	Size	Case Qty	Each	Case	4+ Cases
UNI5748	Dash plate – square corners	3.5” x 2”	50	0.51	0.48	0.47
UNI5733	Dash plate – round corners	3.5” x 2”	50	0.88	0.84	0.83

Transfer Instructions for Unisub Plastics:

* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image”
* Place a sheet of plain white paper on the press.
* Remove the protective plastic covering from the product.
* Using heat resistant tape, secure the image with the printed side of transfer facing the product
* Lay the imprintable face up on the heat press so that you are pressing onto the transfer.
* Cover imprintable with a sheet of plain white paper
* Press at 400 degrees F for 60-70 seconds using Medium pressure
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface

Note: If you are using an item that can be printed on both sides allow the plastic to cool to room temperature before pressing the 2nd side. Refer to the Unisub pressing guide for additional instructions.CLICK HERE

Note: These instructions are guide lines only and are based on the inks, paper, and products we supply. Your inks, papers, etc. may require adjustments in your time/temp settings.

Transfer Instructions for Unisub Metals:

* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image”
* Place a sheet of plain white paper on the press.
* Remove the protective plastic covering from the product.
* Using heat resistant tape, secure the image with the printed side of transfer facing the product
* Lay the imprintable face up on the heat press so that you are pressing onto the transfer.
* Cover imprintable with a smooth absorbant paper towel
* Press at 400 degrees F for 60-70 seconds using Medium pressure
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface
- You can also try pressing the metal from the back side

Note: If you are using an item that can be printed on both sides allow the metal to cool to room temperature before pressing the 2nd side. Refer to the Unisub pressing guide for additional instructions.

Note: These instructions are guide lines only and are based on the inks, paper, and products we supply. Your inks, papers, etc. may require adjustments in your time/temp settings.


	Also Check Out...




		chromaluxe




		starter kits




			sheet stock


	Sublimation Supplies


	Heat Presses


	Printer-Cutter


	Photo Crystals


	Cutters / Plotters


	Direct-To-Garment Printer


	Pad Printing


	Photo Glazing


	Screen Printing


	Heat Transfer Paper


	Heat Transfer Vinyls


	Heat Transfer Film


	ChromaBlast


	Prices and specifications are subject to change without notice. All pricing is reflected in Canadian Funds.