Sublimation Sheet Stock
Note: Image Creations will not be responsible for any shipping damage for any "less than case" purchase of sheet stock.


Sheet Stock Aluminum
Item UNI5570 * Sheet Stock – Aluminum White Gloss 0.030” 1 sided Size 12” x 24” with square corners – Qty 10/case – Broken cases billed as each price
$26.65 ea less than case qty
$22.49 ea per case qty
$20.82 ea per 4+ case qty


Sheet Stock Aluminum
Item UNI5623 * Sheet Stock – Chromaluxe Aluminum White Gloss 0.045”
1 sided Size 12” x 24” – with square corners – Qty 10/case – Broken cases billed as each price
$36.97 ea less than case qty
$31.19 ea per case qty
$28.88 ea per 4+ case qty

Sheet Stock FRP
Item UNI5513 * Sheet Stock – FRP White Gloss 3/32” 1 sided Size 11.5” x 23.25” – Qty 10/case – Broken cases billed as each price
$26.29 ea less than case qty
$22.18 ea per case
$20.54 ea per 4+ cases

Sheet Stock Hardboard
Item UNI10124 * Sheet Stock – Hardboard White Gloss – 1/8” 1 sided
Size 15.5” x 18.5” – Qty 25/case – Broken cases billed as each price
$16.36 ea less than case
$13.80 ea per case
$12.78 ea per 4+ cases
* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image”
* Place a sheet of plain white paper on the press.
* If the product has a protective plastic covering remove it.
* Using heat resistant tape, secure the image with the printed side of transfer facing the product
* Lay the imprintable face up on the heat press so that you are pressing onto the transfer.
* Cover imprintable with parchment or paper
* Aluminum 0.03 = Press at 385 degrees F for 60-65 seconds using Medium pressure
* Aluminum 0.45 = Press at 385 degrees F for 65-70 seconds using Medium pressure
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface
* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image”
* Place a sheet of plain white paper on the press.
* If the product has a protective plastic covering remove it.
* Using heat resistant tape, secure the image with the printed side of transfer facing the product
* Lay the imprintable face up on the heat press so that you are pressing onto the transfer.
* Cover imprintable with parchment or paper
* Press at 385 degrees F for 70-75 seconds using Medium pressure
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface
* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image”
* Place a sheet of plain white paper on the press.
* If the product has a protective plastic covering remove it.
* Using heat resistant tape, secure the image with the printed side of transfer facing the product
* Lay the imprintable face up on the heat press so that you are pressing onto the transfer.
* Cover imprintable with parchment or paper
* Press at 385 degrees F for 70-85 seconds using Medium pressure
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface
These transfer instruction guidelines were created using a Swing-Away GeoKnight Press, size 20″ x 24″/508 x 609.6 mm with pressure of 60 PSI. They represent the best, most general instructions we can provide. Please remember that heat presses may vary. Check with your press manufacturer for any special concerns. This information may change as we make continual improvements and refine our processes. These instructions are guide lines only and are based on the inks, paper, and products we supply. Your inks, papers, etc. may require adjustments in your time/temp settings.