Image Creations Inc.

TEL: 800-260-2704 | Fax: 403-938-1016 | E-Mail: [email protected]

Your Image Transfer Specialists

Sublimation Shrink Sleeve

Sublimation Shrink Sleeves are an alternative to mug wraps or heat press for irregular shaped drink wear and other products. 

Sublimation Shrink Sleeve

 Equipment required is a heat gun, convection oven and heat tape.  

The How To:  
Refer to the settings on the product being sublimated for time and temperature.
* Insure that all plastic parts are removed from item
*  The correct wrap will fit loosely around the product. 
* Position & secure transfer to the product with heat tape.
* Place & center product inside the shrink wrap.·
* Use heat gun on low setting to shrink the wrap to the contour of the product. Begin with the side away from the transfer first. Ensure the wrap only encases the sides of the product leaving top and bottom open.
* Repeat above steps for each item to include in production run.
* When items are ready, place into preheated convection oven.   
* When sublimation time is complete, shrink wrap can be removed.  Caution item will be extremely hot.  DO NOT hancle with bare hands.   DO NOT dunk in water.  

Additional Tips: 
* Using a silicon baking sheet will prevent shrink wrap material from sticking to the oven racks. ·
* Shrink wraps can be cut down in length for better fit.
* Using too small of shrink wrap can result in splitting during the heating process.
* Removing the wrap while still hot will minimize sticking to the product and make removal easier.

Sublimation Shrink Sleeve for 500 ml Coke Bottle

Item SBOT500SHRINK *  White Shrink Sleeve for 500 ml Coke Bottle.  4,7″x 10.2″:
Recommended time and temperature: 330 sec at 375 degrees F Note: Time and Temperatire recommendation is a guide and starting point only as results will vary depending on equipment and substrates.
Qty 20 / pack
$8.00 per pack
$6.40 per 3-5 packs
$5.80 per 6+ packs

Sublimation Shrink Sleeve for Stainless Steel Wine Tumbler

Item SMUG-WSHRINK *  White Shrink Sleeve for Stainless Steelk Wine Tumbler.  5.9″x 6.7″.    Recommended time and temperature: 330 sec at 375 degrees F Note: Time and Temperatire recommendation is a guide and starting point only as results will vary depending on equipment and substrates.
Qty 20 / pack
$7.60 per pack
$6.00 per 3-5 packs
$5.50 per 6+ packs

Sublimation Shrink Sleeve for 20 oz Yetti Style Mug

Item SMUG-20SHRINK *  White Shrink Sleeve for 20 oz Yetti Style Mug,  14 oz SS Travel Mug, Water Bottles etc.   5.3″x 10.2″  Recommended time and temperature: 330 sec at 375 degrees F Note: Time and Temperatire recommendation is a guide and starting point only as results will vary depending on equipment and substrates.
Qty 20 / pack
$8.40 per pack
$6.80 per 3-5 packs
$6.10 per 6+ packs

Sublimation Shrink Sleeve for Dog and Cat Bowl

Item SDB-SHRINK *  White Shrink Sleeve for Ceramic Dog and Cat Bowl.  13″x 5.11″  Recommended time and temperature: 900 sec at 400 degrees F Note: Time and Temperatire recommendation is a guide and starting point only as results will vary depending on equipment and substrates.
Qty 10 / pack
$4.80 per pack
$3.85 per 3-5 packs
$3.50 per 6+ packs