Magnets

Magnet - FRP

Item UNI5522  *  Magnet (frp) Round:  Size 2.55” round
Qty 50/case – Broken cases billed as each.
$1.85 ea less than case
$1.61 ea per case
$1.55 ea per 4+ cases

 

Magnet - FRP

Item UNI5523  *  Magnet (frp) Square:  Size 2.25 x 2.25”
Qty 50/case – Broken cases billed as each.
$1.85 ea less than case
$1.61 ea per case
$1.55 ea per 4+ cases

 

Magnet - FRP

Item UNI5527  *  Magnet (frp) Heart  Size 2.5” x 2.25” 
Qty 50/case – Broken cases billed as each.
$1.85 ea less than case
$1.61 ea per case
$1.55 ea per 4+ cases

 

Magnet - Aluminum

Item UNI5734  *  Magnet Aluminum with 1″ magnet – Size 2” x 3” 
Qty 50/case – Broken cases billed as each.
$2.26 ea less than case
$1.97 ea per case
$1.90 ea per 4+ cases

 

Magnet - Aluminum

Item UNI4052  *  Magnet Hardboard Rectangle w/1” magnet :  Size 2” x 3” x ⅛”
Qty 50/case – Broken cases billed as each.
$2.01 ea less than case
$1.75 ea per case
$1.69 ea per 4+ cases 

 

Magnet - Porcelain

Item SMAG *  Porcelain Magnet   Size 2” x 3 1/4” 
Qty 100/case – Broken cases billed as each.
$3.95 ea less than case
$3.75 ea per case
$3.65 ea per 4+ cases

 

Magnet - Porcelain

Item SHEARTMAG *  Porcelain Magnet   Size 2.75” x 3 1/4”2.75”
Qty 100/case – Broken cases billed as each.
$3.95 ea less than case
$3.75 ea per case
$3.65 ea per 4+ cases

 

* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image” to insure correct application
* Place a neomex felt pad on the bottom platform of the press
* Lay the imprint transfer face up on the neomex pad
*  The product is placed coated side face down. (the artwork is between the product and the nomex pad)
 
* Cover product with a sheet of plain white paper.
    
* Press at 400 degrees F for 4-5 minutes using Medium to heavy pressure
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface

Note: These instructions are guide lines only and are based on the inks, paper, and products we supply. Your inks, papers, etc. may require adjustments in your time/temp settings.

* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image” 
* Place a sheet of plain white paper on the press.
* If the product has a protective plastic covering remove it.
* Using heat resistant tape, secure the image with the printed side of transfer facing the product
* Lay the imprintable face up on the heat press so that you are pressing onto the transfer.
* Cover imprintable with parchment or paper 
* Press at 400 degrees F for  60-65 seconds using Medium pressure
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface

Note: These instructions are guide lines only and are based on the inks, paper, and products we supply.   Your inks, papers, etc. may require adjustments in your time/temp settings.

* Prepare artwork and size transfer according to the size and shape of the product.
* Image must be produced in reverse or “mirror image” 
* Place a sheet of plain white paper on the press.
* If the product has a protective plastic covering remove it.
* Using heat resistant tape, secure the image with the printed side of transfer facing the product
* Lay the imprintable face up on the heat press so that you are pressing onto the transfer.
* Cover imprintable with parchment or paper 
* Press at 400 degrees F for 60-70 seconds using Medium pressure (single side)
* Press at 400 degrees F for 75-85 seconds using Medium pressure (double side) 2 sides at a time
* When pressing is finished carefully remove the transfer paper and allow to cool on a clean surface

Note: If you are using an item that can be printed on both sides allow the metal to cool to room temperature before pressing the 2nd side.  Refer to the Unisub pressing guide for additional instructions.

Note: These instructions are guide lines only and are based on the inks, paper, and products we supply.   Your inks, papers, etc. may require adjustments in your time/temp settings.